Uses of Class
us.gov.dod.standard.ssrf._3_1.transmitter.ObservedRFAnalysis

Packages that use ObservedRFAnalysis

Package	Description
us.gov.dod.standard.ssrf._3_1.transmitter

Uses of ObservedRFAnalysis in us.gov.dod.standard.ssrf._3_1.transmitter

Methods in us.gov.dod.standard.ssrf._3_1.transmitter that return ObservedRFAnalysis

Modifier and Type	Method and Description
ObservedRFAnalysis	ObservedRFAnalysis.withChipRate(Double value) Set the chip rate.
ObservedRFAnalysis	ObservedRFAnalysis.withDwellTime(Double value) Set the dwell time at any RF when the RF dwells at particular values for more than one pulse in a row.
ObservedRFAnalysis	ObservedRFAnalysis.withFreqMax(Double value) Set the upper end of the range of RF values that represent 100% of observed signals.
ObservedRFAnalysis	ObservedRFAnalysis.withFreqMin(Double value) Set the lower end of the range of RF values that represent 100% of observed signals.
ObservedRFAnalysis	ObservedRFAnalysis.withGuardBand(Double value) Set the RF band between carriers which is not used.
ObservedRFAnalysis	ObservedRFAnalysis.withInstantRFBW03(Double value) Set the transmitter pulse bandwidth (burst or instantaneous) measured at the 3 dB points (min)
ObservedRFAnalysis	ObservedRFAnalysis.withInstantRFBW06(Double value) Set the transmitter pulse bandwidth (burst or instantaneous) measured at the 6 dB points (min)
ObservedRFAnalysis	ObservedRFAnalysis.withInstantRFBW10(Double value) Set the transmitter pulse bandwidth (burst or instantaneous) measured at the 10 dB points (min)
ObservedRFAnalysis	ObservedRFAnalysis.withInstantRFBW20(Double value) Set the transmitter pulse bandwidth (burst or instantaneous) measured at the 20 dB points (min)
ObservedRFAnalysis	ObservedRFAnalysis.withNumRFChannels(Integer value) Set the number of channels into which the RF range of the emitter is divided.
ObservedRFAnalysis	ObservedRFAnalysis.withNumRFElements(Integer value) Set the number of discrete RFs (channels) a multiple RF signal contains.
ObservedRFAnalysis	ObservedRFAnalysis.withNumRFPositions(Integer value) Set the number of RF values in a signal RF sequence before it repeats.
ObservedRFAnalysis	ObservedRFAnalysis.withNumRFSimultaneous(Integer value) Set The number of frequencies simultaneously used by the emitter.
ObservedRFAnalysis	ObservedRFAnalysis.withObservedRFValues(Collection<ObservedRFValues> values) Set the US:ObservedRFValues
ObservedRFAnalysis	ObservedRFAnalysis.withObservedRFValues(ObservedRFValues... values) Set the US:ObservedRFValues
ObservedRFAnalysis	ObservedRFAnalysis.withOperationalRFBW(Double value) Set the delta (aka.
ObservedRFAnalysis	ObservedRFAnalysis.withRFAdaptiveDriver(String value) Set the condition controlling the choice of RF for Adaptive RF variations (e.g., least jammed frequency)
ObservedRFAnalysis	ObservedRFAnalysis.withRFAdaptiveRule(String value) Set In Data Item RFAdaptiveRule (US), indicate how the RF is chosen for Adaptive RF variations.
ObservedRFAnalysis	ObservedRFAnalysis.withRFBasicClockPeriod(Double value) Set the frequency divisor common to all RF separations (not necessarily to all RF) RF crystal is not always the same as the RF channelization (min).
ObservedRFAnalysis	ObservedRFAnalysis.withRFChangeRate(Double value) Set the RF change per unit of time, measured over a significant portion of the waveform.
ObservedRFAnalysis	ObservedRFAnalysis.withRFChannelFreqMax(Double value) Set the maximum RF channel values.
ObservedRFAnalysis	ObservedRFAnalysis.withRFChannelFreqMin(Double value) Set the minimum RF channel values.
ObservedRFAnalysis	ObservedRFAnalysis.withRFCoherent(ListUSY value) Set In Data Item RFCoherent (US), indicate if the observed RF signal is coherent, non-coherent, or unknown.
ObservedRFAnalysis	ObservedRFAnalysis.withRFContinuous(ListCBO value) Set whether pulse-to-pulse RF variations are Discrete or Continuous.
ObservedRFAnalysis	ObservedRFAnalysis.withRFFreqMax(Double value) Set the typical highest RF value observed on a single intercept.
ObservedRFAnalysis	ObservedRFAnalysis.withRFFreqMin(Double value) Set the typical lowest RF value observed on a single intercept.
ObservedRFAnalysis	ObservedRFAnalysis.withRFFreqTolerance(Double value) Set the drift in Hz or in ppm using the formula: Frequency tolerance (ppm) = Maximum drift (Hz) / Center frequency (MHz).
ObservedRFAnalysis	ObservedRFAnalysis.withRFFreqToleranceInterval(Double value) Set In Data Item:RFFreqToleranceInterval (US), enter the time interval over which the RF stability measurements were taken.
ObservedRFAnalysis	ObservedRFAnalysis.withRFFreqToleranceUnit(ListCFO value) Set the units in which the Frequency Tolerance is expressed.
ObservedRFAnalysis	ObservedRFAnalysis.withRFMean(Double value) Set the average RF of a signal which changes RFs on a non-patterned basis.
ObservedRFAnalysis	ObservedRFAnalysis.withRFMedian(Double value) Set the most probable RF values.
ObservedRFAnalysis	ObservedRFAnalysis.withRFPatternPeriod(Double value) Set the duration of one cycle of the pattern for patterned RF variations.
ObservedRFAnalysis	ObservedRFAnalysis.withRFPatternType(ListUS7 value) Set In Data Item RFPatternType (US), Indicate whether RF is unmodulated or pulse-to-pulse RF variations are Patterned, Non-Patterned, or Adaptive.
ObservedRFAnalysis	ObservedRFAnalysis.withRFRestFreq(Double value) Set the observed carrier or rest frequency when the modulation is off.
ObservedRFAnalysis	ObservedRFAnalysis.withRFSequenceDesc(String value) Set a free text description of the RF Sequence.
ObservedRFAnalysis	ObservedRFAnalysis.withRFSlotDuration(Double value) Set the duration of a single time slot for the hop dwell.
ObservedRFAnalysis	ObservedRFAnalysis.withRFStandardDeviation(Double value) Set the standard deviation of the data set used to calculate RF Mean.
ObservedRFAnalysis	ObservedRFAnalysis.withRFTuningStep(Double value) Set the separation between the mean RF values of adjacent RFs in signal with discrete RF channels.
ObservedRFAnalysis	ObservedRFAnalysis.withTuningStep(Double value) Set the separation between the mean RF values of adjacent RFs in signal with discrete RF channels.

Methods in us.gov.dod.standard.ssrf._3_1.transmitter that return types with arguments of type ObservedRFAnalysis

Modifier and Type	Method and Description
Set<ObservedRFAnalysis>	TxMode.getObservedRFAnalysis() Get the US:ObservedRFAnalysis

Methods in us.gov.dod.standard.ssrf._3_1.transmitter with parameters of type ObservedRFAnalysis

Modifier and Type	Method and Description
TxMode	TxMode.withObservedRFAnalysis(ObservedRFAnalysis... values) Set the US:ObservedRFAnalysis

Method parameters in us.gov.dod.standard.ssrf._3_1.transmitter with type arguments of type ObservedRFAnalysis

Modifier and Type	Method and Description
TxMode	TxMode.withObservedRFAnalysis(Collection<ObservedRFAnalysis> values) Set the US:ObservedRFAnalysis